One ceiling fixture, five diameters, field-set output
A brushed-nickel flush mount built around a 120V platform, where the installer decides the wattage and the colour of the light on the day it goes up.
The housing is stainless steel finished in brushed nickel. Its satin grain is deliberately low-key: it sits quietly against painted plaster, timber and the mixed metalwork of a modern interior instead of turning the ceiling into a mirror. The low-profile form keeps the fitting close to the surface, which matters in corridors and rooms with modest ceiling heights.
A frosted polycarbonate lens closes the housing. It hides the individual diodes and spreads their output into a single even field, so the fitting reads as a soft disc of light rather than a cluster of bright points. Polycarbonate also resists the knocks that a glass diffuser would not survive in a busy circulation area.
Behind that lens, two selectors set the character of the fitting. Wattage can be stepped between three levels and colour temperature across five positions from 2700K to 5000K. A distributor can therefore hold one model per diameter and still serve a warm residential scheme and a cooler commercial one from the same carton.
The specification at a glance
- ✓Brushed nickel stainless-steel housing
- ✓Frosted polycarbonate lens
- ✓10 / 12 / 14 / 16 / 18 inch diameters
- ✓Selectable wattage, three levels per model
- ✓Five switchable CCT positions, 2700K to 5000K
- ✓Triac dimmable, 120V input
- ✓50000-hour rated life, Energy Star listed
- ✓Optional sensor for shared areas
Eight decisions that make it easy to specify
Set the wattage on site
Each diameter offers three selectable power levels. The 10 and 12 inch versions step through 8-12-16W, while the 18 inch reaches 22-30-36W, so one fitting can be tuned to the room instead of over-lighting it.
Five colour temperatures
A 27/30/35/40/50K selector covers warm residential light through to a crisp 5000K for task areas, without ordering separate SKUs for each tone.
Triac dimming as standard
The driver works with conventional Triac wall dimmers on a 120V circuit, which keeps installation compatible with the controls already on a North American project.
Even, glare-free output
The frosted polycarbonate lens diffuses the diode array into one continuous surface, softening the beam and keeping the ceiling comfortable to look up at.
A finish that stays quiet
Brushed nickel stainless steel resists fingerprints and reads as a restrained satin trim, working equally well beside warm timber and cool grey joinery.
Power factor and colour rendition
PF of 0.9 or higher and CRI of 80 or higher are held across the range, so large orders stay consistent on both the electrical and the visual side.
Rated for the long run
A 50000-hour rated life and Energy Star listing make the fixture a sensible choice where relamping is disruptive or access is difficult.
Sensor-ready
An optional sensor can be fitted for corridors, stairwells and shared spaces, cutting run hours without adding a separate control system.
Match the diameter to the space
All five models share the brushed nickel finish, the frosted lens, Triac dimming, the five-position CCT selector and the 120V input. What changes is diameter, the wattage steps and the delivered lumens.
FXF23001 · 10 inch · 1200lm
Compact bedrooms, utility rooms and short hallways. Its 8-12-16W selector lets the installer keep the output gentle in a small footprint without changing the fitting.
FXF23002 · 12 inch · 1200lm
Kitchens, dressing areas and en-suites that need a familiar mid-size flush mount. Same 8-12-16W steps, with a slightly wider diffuser spreading the same lumen package.
FXF23003 · 14 inch · 1650lm
Main bedrooms, home studies and small reception rooms. Wattage steps up to 12-16-22W, giving enough headroom for a room used through the whole evening.
FXF23004 · 16 inch · 2250lm
Living rooms, open kitchens and commercial offices. The 16-22-30W range covers a wider floor area while the lens keeps the source visually soft.
FXF23005 · 18 inch · 2700lm
Large lounges, meeting rooms and public circulation zones. At 22-30-36W it is the highest-output model, with the sensor option most often specified here.
The original five-model specification
Values below follow the factory data sheet. Each column of the source table refers to one item code, from FXF23001 on the left to FXF23005 on the right.
Where a selectable fixture earns its keep
Residential Ceilings
Bedrooms, kitchens, dressing rooms and entrance halls take the 10 to 14 inch models, where a warm 2700K or 3000K setting and a low-profile body keep the room relaxed.
Apartments & Multi-Family
A single design language across every unit, with one stocked diameter per room type and the wattage selector set during commissioning rather than at order stage.
Commercial Offices
The 16 and 18 inch versions at 4000K give meeting rooms and open work floors an even field of light, with CRI 80 or above keeping printed material readable.
Public Corridors & Stairwells
The frosted polycarbonate lens stands up to traffic, and the optional sensor trims running hours in circulation zones that are empty for much of the day.
Retail & Hospitality Back-of-House
Brushed nickel sits comfortably beside stainless fittings in service areas, while the 3500K or 4000K position suits staff spaces without a separate product line.
Retrofit & Renovation Projects
Triac dimming and a 120V input let an existing wall control and circuit stay in place, which is what makes a like-for-like ceiling replacement straightforward.
What is verified before the carton closes
Finish batching
Brushed nickel housings are compared under the same light so the satin grain and tone stay consistent across a multi-floor order rather than varying carton to carton.
Lens fit and diffusion
Each frosted polycarbonate lens is checked for seating and for an unbroken light field, with no diode imaging and no gap at the housing edge.
Selector verification
Every unit is stepped through its three wattage levels and its five CCT positions before packing, confirming that the switch maps to the correct driver setting.
Dimmer compatibility
Triac dimming is exercised across the control range on a 120V supply, watching for drop-out, flicker and audible noise at the low end.
Electrical measurement
Power factor of 0.9 or above and CRI of 80 or above are verified on the finished assembly, not only on the component data sheet.
Burn-in and listing
Extended run-in supports the 50000-hour rating, and the construction is held to the Energy Star listed configuration for every production batch.
Built around the specification you are bidding
Most requests start from a schedule rather than a sketch: a list of diameters, a target lumen package, a preferred CCT and the control gear already specified on site. Our engineering team maps those requirements onto the five-model platform and confirms which selector positions, lens finish and housing tone should be locked for the run.
Private-label work is routine, from a distributor's own carton artwork and label set to a fixed 3000K-only or 4000K-only build for a hotel group. Sensor-equipped variants, non-standard wattage steps and project-specific packaging quantities can all be quoted against a defined volume.
Because the housing, lens and driver platform are produced in one workshop, a change to the finish or the selector map does not require a new tooling programme. That keeps a tailored build realistic at contract quantities rather than only at container loads.
Send the schedule
Share diameters, quantities, target lumens, CCT, dimmer type and any labelling requirements.
Sign off a build sample
A configured unit is produced so the brushed nickel tone, lens diffusion and CCT positions can be assessed together.
Run and inspect
Selector, dimmer and electrical checks are repeated on the production batch before cartons are sealed.
Setting it up, keeping it clean
Mounting and commissioning
Isolate the 120V circuit, fix the low-profile base to the ceiling and make the supply connection to the driver. Set the wattage and CCT selectors before the lens is closed; they are far easier to reach while the housing is open than from a ladder afterwards.
If a Triac wall dimmer is in circuit, run the fitting through its full dimming range once power is restored. Where the optional sensor is fitted, allow a short commissioning period to set its coverage for the corridor or stairwell rather than the adjacent room.
Cleaning and service
The frosted polycarbonate lens lifts off for cleaning. Use a soft dry cloth or a mild soap solution; avoid solvents, scouring pads and anything abrasive, all of which can cloud the diffuser. Wipe the brushed nickel housing along the grain with a dry cloth.
With a 50000-hour rated life there is no routine relamping schedule to plan around. If the fitting ever needs attention, isolate power first and work from the base so the lens and its seating are not disturbed.
Points raised before an order is placed
1. Can the wattage and colour temperature be changed after installation?
They are set with selectors inside the housing, so the decision is normally made at commissioning. If a room changes use later, the lens can be lifted and the positions reset without replacing the fitting or altering the 120V wiring.
2. Which diameter should I choose for a given room?
10 and 12 inch at 1200lm suit bedrooms and utility spaces; 14 inch at 1650lm covers a main bedroom or study; 16 inch at 2250lm fits a living room or office; 18 inch at 2700lm serves larger lounges and circulation areas.
3. Does it work with an existing wall dimmer?
Yes. All five models are Triac dimmable on a 120V supply, which is the control standard on most North American residential and light-commercial circuits. We recommend checking the low end of the dimmer range during commissioning.
4. Can you build custom lights or add our logo?
Yes. We configure selector maps, finishes, sensor variants and packaging for project schedules, and apply a customer's logo and label artwork to bulk orders. Share the specification and quantity and our team will come back with the options.
5. May we visit the factory to review a build?
Visits are welcome at our Hangzhou workshop. Seeing the brushed nickel finish, the lens diffusion and a configured sample together is often the quickest way to close out a specification before a full order is released.
Hot Tags: led ceiling fixtures, China led ceiling fixtures manufacturers, suppliers, factory, indoor lighting fixtures that are distributed, indoor lighting fixtures that are wholesaled
