Ceiling LED Light In Room

Fixing begins with a base plate mounted to a firm ceiling or junction box. The supply is terminated once, the lamp body is offered up to the base and aligned, then a few screws or spring buckles hold it in place. Because nothing is suspended, there is no chain, cable or canopy to adjust afterwards and nothing swinging into the room.

The practical benefit is time on site. An installer working through a flat or a hotel floor can repeat the same short sequence room after room, and a homeowner replacing an old fitting in a bedroom or living room does not need a second pair of hands to support a heavy pendant while the connections are made.

At only 25 mm deep, the finished light reads as part of the ceiling rather than an object hanging below it, which also keeps headroom intact in corridors and rooms with lower soffits.

What the mounting method gives you

• ✓Direct-to-ceiling surface fixing
• ✓Screws or buckles, no hanging kit
• ✓Simple termination, no complex wiring
• ✓Shallow H25 mm profile
• ✓Repeatable install across many rooms
• ✓220–240V mains operation

One base, one position

Mark the ceiling, drill for the base plate and fix it to a solid surface or the existing junction box before any wiring is handled.

Power isolated first

Switch off the circuit at the breaker, then bring the 220–240V supply to the base and terminate live and neutral to the terminals.

Body offered up flat

The shallow housing is lifted against the base and aligned by eye; there is no pendant to balance while the connections are checked.

Screws or buckles

Either tighten the fixing screws or press the buckles home until the body sits flush, with no gap around the perimeter.

No suspension hardware

No chains, drop rods, canopies or ceiling hooks are required, which removes the most common source of rework on a fitting like this.

Switch on and confirm

Restore power and verify even output across the face; the tight ±10% tolerance keeps brightness consistent from room to room.

7 inch · 15W · 1240lm

Φ190×H25 mm. A compact bedroom, box room or short hallway where a single quiet fitting covers the whole ceiling.

9 inch · 18W · 1440lm

Φ230×H25 mm. A standard double bedroom or home office, comfortably bright without over-lighting a modest floor area.

12 inch · 24W · 1920lm

Φ300×H25 mm. A main living room, dining area or larger master suite needing one central fitting with even spread.

16 inch · 30W · 2500lm

Φ400×H25 mm. Open-plan living space, shared lounge or a wide room where a smaller panel would leave the corners dim.

Bedrooms & Guest Rooms

A flat, quiet fitting over the bed area. Swapping an old ceiling light takes minutes because the base fixes directly to the existing ceiling point.

Living Rooms & Lounges

One 12 or 16 inch panel gives even general light without a pendant dropping into the sightline of a television or a conversation area.

Rental Flats & Refurbishments

Landlords and refurbishment crews value a repeatable fitting that needs no new suspension point and can be replaced like-for-like between tenancies.

Low-Ceiling Corridors

The 25 mm depth keeps clearance in hallways, utility passages and under-mezzanine areas where a hanging fixture would be in the way.

Multi-Site Retail Rollouts

Fixed carton counts per diameter let a distributor split a container across several shop formats without repacking at the destination.

Hotels & Serviced Apartments

Hundreds of identical rooms are fitted with the same short sequence, and a spare unit can be swapped in without disturbing the ceiling finish.

Sample before the run

A pre-production sample is arranged and approved before mass production starts, so the agreed finish and output are fixed in advance.

Aging on every piece

All units go through a 100% aging test during production rather than a spot check on a few cartons from the line.

Final check at dispatch

A final inspection is carried out before shipment, covering appearance, fixing parts and the light output of the batch.

Tolerance held to 10%

Both wattage and lumen are kept inside ±10%, so fittings from different cartons look the same when installed side by side.

Carton counts fixed

40, 20, 10 and 10 pieces per carton for the 7, 9, 12 and 16 inch versions; the count does not drift between batches.

Carton sizes published

Outer dimensions of 40×27×40, 48×27×25, 32×27×32 and 42×27×42 cm are given per size for container planning.

Samples are available on request and travel by express courier, so the mounting base, the 25 mm profile and the light itself can be checked on a real ceiling before a container is committed.

Regular production runs 25 to 30 days, with the final date depending on order volume and the exact mix of diameters. Rush orders are accepted - send the required quantity and deadline and the workshop will confirm the earliest available slot.

Because each diameter has its own published carton count and outer size, a mixed order can be planned against a specific container or pallet footprint from the outset rather than estimated after packing.

In transit and in store

The packaging and specification design is built around the realities of shipping: cartons are sized to the fitting, stack predictably and are easy to count on receipt. Keep them dry and upright, avoid crushing loads on the shallow profiles, and store by diameter so a mixed order can be picked without opening every box.

Published outer dimensions make it straightforward to work out pallet layers and container utilisation before the goods leave the factory, which is often where the real saving on a bulky lighting line is found.

Once installed

With no hanging parts and no complex wiring, there is very little to go wrong in service. A periodic wipe with a soft dry cloth keeps the face clean; if a unit ever needs replacing, only the fixing screws or buckles are released and the body lifts away from the base.

That combination - simple fitting, sensible packing and low upkeep - is what keeps both installation cost and long-term maintenance effort down across a large number of rooms.