Built for rooms where eyes work for hours
A quality driver, a flicker-free output and an anti-glare face combine into a fitting aimed at classrooms, offices and study spaces rather than occasional passage lighting.
Most complaints about ceiling lighting are not about brightness but about what the light does over a long sitting. Rapid pulsing that the eye barely registers still leads to fatigue and small misreadings on a page or screen, so this unit is built to hold a steady, flicker-free output from switch-on to switch-off.
The face is treated against glare as well. By limiting reflection and refraction at the surface, the beam reaches desks without the harsh bounce that makes people tilt their heads or shield their eyes. Together with a driver that lights instantly, the result is a room that is simply comfortable to stay in.
What the fitting is specified around
- ✓Flicker-free steady output
- ✓Anti-glare treated surface
- ✓Instant start, no warm-up
- ✓3CCT colour temperature
- ✓Chip count matched per wattage
- ✓ABS + PS, tough and wipeable
Three decisions behind the light
No visible flicker
Steady drive removes the pulsing linked to eye strain and visual errors, which matters most where reading, writing or screen work continues all day.
Glare held at the face
Surface treatment reduces reflection and refraction, so the light lands on the task instead of bouncing back into the eyes.
On at the touch of a switch
A high-quality driving supply brings the panel to full output immediately, with no delay, ramp-up or audible start-up noise.
Chips sized to the load
The number of chips is matched to each wattage rather than reused across sizes, keeping output stable and the light quality consistent.
A housing that copes
ABS + PS combines strength with a clean appearance, adapts to different interiors, resists knocks and wipes clean with a cloth.
Printable lamp face
A corporate logo or a bespoke pattern can be printed directly on the surface for branded projects and retail programmes.
Specify by the task in the room
All four diameters share the same 3CCT and dimmable platform; the choice is the area to be covered and the wiring planned at install.
7 inch · 15W
Φ190×H25 mm, PF above 0.7. A small study, consulting room or corridor where a single quiet panel is sufficient.
9 inch · 18W
Φ230×H25 mm, PF above 0.7. A home office or tutorial room, sized for one or two desks under long evening use.
12 inch · 24W
Φ300×H25 mm, PF above 0.7. A standard classroom bay or shared office zone that needs even coverage across several worktops.
16 inch · 30W
Φ400×H25 mm, PF above 0.9. A large training room or open-plan floor where many fittings run together for the whole day.
Specifications by body size
Rooms that benefit most
School Classrooms
Children and teachers sit under the light for hours; flicker-free output and a glare-treated face keep reading and board work comfortable.
Open Offices
Rows of panels run all day over screens and documents. A PF above 0.9 on the largest size helps when many units share one circuit.
Libraries & Reading Rooms
Steady, even light without a visible bright point lets readers stay at a table without the low-level strain of pulsing sources.
Home Study Corners
A 7 or 9 inch panel gives a child or remote worker a calm task light, with 3CCT to shift from daytime focus to a softer evening tone.
Design & Drafting Studios
Anti-glare treatment matters where glossy prints and tablets lie flat; instant start means no pause when the room is switched on.
Clinics & Reception Desks
Easy-clean ABS + PS and a printable lamp face suit branded front-of-house areas that also need comfortable all-day illumination.
From driver to carton
Driver selected first
The supply is chosen for a clean, instant start and a steady current, because flicker performance is decided there before any lens is fitted.
Chip count per wattage
Each of the four power ratings gets its own chip layout, verified for stable output rather than borrowed from a single board.
Surface checks
Sample faces are inspected for the anti-glare finish, print adhesion where logos are applied, and freedom from marks before packing.
Impact and wiring tests
IK05 housings, 2*0.75mm² leads and PF readings are checked against the size being built.
Export experience
Consolidated sea and air shipments to the Americas, Europe, the Gulf and Oceania with the full document set.
Project documentation
Wiring diagrams, size-to-wattage charts and dimmer notes travel with each quotation for school and office tenders.
Put your mark on the lamp face
Beyond the usual choice of diameter, wattage and colour temperature, this range accepts personalised printing on the surface of the fitting itself. Send the corporate logo or a bespoke pattern and we apply it to the lamp face, then repeat the artwork on the carton so a project arrives branded end to end.
Typical briefs include a school authority marking every classroom panel, a 16 inch / 30W SKU held as a single line for an office fit-out, and a 3CCT variant packed under a distributor's own label.
Define the brief
Diameter, wattage, colour-temperature setting, artwork file and quantity.
Approve a printed sample
A physical face print and a lit photo are sent for sign-off before the run.
Produce and verify
Print adhesion, output steadiness and wiring are checked inline through production.
Wiring and routine care
At installation
Isolate the circuit, fix the base to the junction box or a firm ceiling, and terminate the 2*0.75mm² supply lead to live and neutral. If a dimmer is part of the scheme, match it to the driver before energising. Switch on and confirm the instant, steady light with no visible pulsing.
In service
The ABS + PS face is easy to clean - wipe with a soft, slightly damp cloth and avoid solvents or abrasives that could dull the anti-glare finish. Where a logo has been printed, clean around it gently to preserve the artwork.
Before placing an order
1. Why do flicker-free and anti-glare matter?
Rapid pulsing and reflected glare are both linked to eye fatigue and small visual errors over long sittings. Removing them makes classrooms, offices and reading rooms more comfortable to work in.
2. Does the lamp need time to warm up?
No. A high-quality driving supply brings it to full output immediately when the switch is pressed, with no ramp-up or waiting.
3. Which size and wattage should I order?
7 inch / 15W, 9 inch / 18W, 12 inch / 24W and 16 inch / 30W, all within ±10%. The 16 inch version carries a power factor above 0.9; the smaller three are above 0.7.
4. What does 3CCT mean, and is it dimmable?
3CCT means three selectable colour temperatures on the same fitting, and the driver supports brightness adjustment. Confirm the dimmer type with us at quotation so the pairing is right for your site.
5. Can our logo be printed, and what is the MOQ?
Yes - a corporate logo or bespoke pattern can be printed on the lamp face and repeated on the carton. Minimum order quantity depends on the specification and is confirmed per project, with samples supplied for approval.
Hot Tags: dimmable led ceiling light, China dimmable led ceiling light manufacturers, suppliers, factory, indoor lighting fixtures that are distributed, indoor lighting fixtures that are wholesaled
