A 25 mm disc that sits almost flush
Four diameters, four declared wattages and a shade that stays white - a plain ceiling plate scaled from a compact aisle to a spacious conference room.
Height is the detail that changes a room. At just 25 mm, the plate barely breaks the ceiling line, which keeps low soffits and narrow passages feeling open instead of crowded by a bulky housing.
The shade is the second half of the story. Rather than exposing a cluster of bright points, it scatters the beam across its whole face, so the light arrives as a soft, even wash with no glare directly beneath the fitting.
The three-part assembly
- ✓Body: fixes the source, takes the wiring
- ✓Shade: shields and spreads the beam evenly
- ✓LED source: 1240 to 2500 lm by size
- ✓ABS + PS, anti-ageing and shape-stable
- ✓Only 25 mm deep in every diameter
- ✓CRI above 80, 3000K or 4000K
Why the material matters
Stays white over time
The ABS+PS blend is chosen for anti-ageing performance, so the shade resists the yellowing and warping that cheap plastic shows after seasons of heat and daylight.
Even diffusion
Light is scattered across the full face of the shade instead of beaming from a visible point, giving a calm, uniform result on walls and floors.
True-to-life colour
A colour rendering index above 80 keeps fabrics, wood and food looking as they should - close to the effect of a studio fill light.
Lower running cost
Selected models reach a power factor above 0.9, cutting reactive draw and trimming electricity spend while the fitting still delivers its rated lumen output.
Four declared wattages
15W, 18W, 24W and 30W align with the four diameters, so a buyer can budget load and brightness before a single unit is ordered.
IK05 housing
The body carries an IK05 rating, enough to tolerate the small knocks of installation, cleaning and everyday use in busy areas.
Read the size against the floor plan
Each step up in diameter raises both the wattage and the lumen package, so the range covers a passage at one end and a meeting room at the other.
7 inch · 15W
Φ190×H25 mm, about 1240 lm. A compact aisle, entry or utility nook where a modest, unobtrusive plate is all that is needed.
9 inch · 18W
Φ230×H25 mm, about 1440 lm. A bedroom or small study that wants a soft general light without a large visible disc.
12 inch · 24W
Φ300×H25 mm, about 1920 lm. A standard living or dining area, balanced between coverage and a restrained ceiling profile.
16 inch · 30W
Φ400×H25 mm, about 2500 lm. A spacious conference room, open office or shared lounge needing one central fitting.
Specifications by body size
Where a low-profile plate fits
Aisles & Corridors
The 7 inch plate and its 25 mm depth keep a narrow passage clear, while the diffused face avoids a glaring spot at eye level.
Conference & Meeting Rooms
A 16 inch / 2500 lm version covers a wide table evenly; CRI above 80 keeps printed material and faces natural on camera.
Bedrooms
3000K with a 9 or 12 inch body gives a restful general light, and the flat disc stays visually quiet above a bed.
Kitchens & Utility Areas
4000K and the higher lumen steps brighten work surfaces, while the ABS+PS shade wipes clean and resists steam-ageing.
Retail & Showroom
Uniform diffusion shows merchandise without hot spots, and a power factor above 0.9 helps when many fittings run all day.
Hotels & Served Apartments
One plate family covers corridors, rooms and lobbies, so a property can standardise spares across very different spaces.
How the plates are made
Ceiling plates since 2004
Two decades of moulding shades and shipping flush fittings to distributors on several continents stand behind each order.
Material lot control
ABS+PS compound is checked per lot so the anti-ageing behaviour and shade colour stay consistent across a full production run.
Flux and PF verification
Every batch is sampled for lumen output against the ±10% band, power factor and the declared 3000K / 4000K tone.
Impact and ageing tests
Sample housings go through IK05 impact checks and heat soak before a size is cleared for packing.
Freight and documents
Sea and air consolidated to the Americas, Europe, the Gulf and Oceania with a complete export paper set.
Tender-ready drawings
Diameter, cut-out and wattage charts are supplied with quotations for specifiers and project bids.
Build the range under your label
The platform - a 25 mm ABS+PS disc in four diameters, with a choice of 3000K or 4000K - is straightforward to tailor. We can hold one size and wattage for a housing scheme, set a single colour temperature across an order, change the shade finish, or print your logo on both the fitting and the carton for bulk quantities.
Common briefs include a 12 inch / 24W SKU for a residential programme, a 4000K-only version for offices, and retail boxes carrying the buyer's own artwork and barcode.
Send the specification
Diameter, wattage, colour temperature, finish, logo artwork and target quantity.
Approve the pre-production sample
Shade colour, diffused output and printed carton photographed for sign-off.
Production with inline QC
Ageing, flux and appearance checks recorded through the run before dispatch.
Fitting and upkeep
On the ceiling
Isolate the supply, fix the body to the junction box or a solid ceiling, connect live and neutral, then seat and lock the shade. Because the unit is only 25 mm deep, check that the ceiling surface is flat so the rim sits evenly all round.
Over the years
Dust the shade with a soft dry cloth; avoid solvents and scouring pads that could mark the diffuser. The ABS+PS blend resists yellowing, but keeping the fitting out of direct, prolonged moisture will preserve the finish.
Answers before you order
1. Which wattage comes with which size?
7 inch is 15W / 1240 lm, 9 inch is 18W / 1440 lm, 12 inch is 24W / 1920 lm and 16 inch is 30W / 2500 lm, all within a ±10% band.
2. How thin is the fitting?
Every diameter shares the same 25 mm height, from Φ190 up to Φ400 mm across, so the profile stays flat even on the largest plate.
3. Will the shade turn yellow?
The ABS+PS material is specified for anti-ageing performance, so it resists discolouring and deforming under long-term heat and daylight.
4. Can our logo go on the products?
Yes - OEM branding on the fitting and printed cartons is available for bulk orders; artwork and quantity are confirmed at quotation.
5. What are the MOQ, quality checks and factory visit options?
Minimum order quantity varies by item and is quoted per project. Every unit is aged and sampled for flux and appearance, and buyers are welcome to visit our Hangzhou factory, with airport pickup arranged on request.
Hot Tags: led ceiling lamp, China led ceiling lamp manufacturers, suppliers, factory, indoor lighting fixtures that are distributed, indoor lighting fixtures that are wholesaled
